How do I change the sensitivity on my Compustar?

Hold down the vehicle's brake. Press the lock button 3 times on the Compustar/Arctic Start remote. The car will chirp and flash its lights to indicate the current sensitivity of the shock sensor. Press lock to increase the sensitivity, or unlock to decrease the sensitivity.

Furthermore, how do I adjust the sensitivity on my car alarm?

The sensitivity of a car alarm is usually set on the shock sensor, which is going to be a small box that's about three square inches underneath the dashboard on the driver's side. You can adjust this shock sensor by moving the adjustment dial. Turning it counter clockwise will turn it down.

Also Know, how do I change my Compustar run time? Adjust the time settings by tapping the Lock button to change the hour and Unlock button to adjust the minute. STEP 3: Once the time has been set, exit remote programming by holding down the Trunk and Start/Stop buttons for 2.5 seconds. The remote will beep indicating that you have successfully exited programming mode.

Herein, how do I reset my Compustar alarm?

You must cycle the vehicle's ignition between the on and acc/off position 5 times within 7 seconds or less and then tap the lock button, button I, or put the battery in the remote (2WSSR / P2WSSR). The process depends on which remote(s) you have. All your remotes must be reprogrammed at the same time.

How do I adjust the sensitivity on my Karr alarm?

I had to call Karr to get assistance.

To adjust sensitivity do the following:

1. Key on/off.
2. Hold the valet button for ~5 seconds.
3. Press the button the # of times you want the sensitivity, from 1 (lowest) to 10 (highest)

Related Question Answers

How do I set my car alarm?

How to Activate a Car Alarm

1. Get your key fob and locate the lock button. The lock button might read "Lock" in small print or it may include a picture of a lock in its locked position.
2. Press the lock button once. Press it quickly and use pressure.
3. Listen for a beeping sound. Some vehicles activate the alarm after one press of the button.

Can you add shock sensor factory alarm?

Add shock sensor.com

with the shock sensor add-on your factory OEM alarm system will work just like an aftermarket alarm. Your vehicle will have rims, tires and glass bumper to bumper protection, no need to carry an extra remote control around your key chain.

What is a shock sensor on a car alarm?

A shock sensor detects an impact to the body of the vehicle, such as someone hitting a door panel. It helps protect the body of your car plus will act as a warning to a potential thief that an alarm is fitted (thieves will often whack the vehicle to test if it has an alarm).

Why does my car alarm keep going off for no reason?

If your key fob is not functioning properly, it may send the wrong signal to your vehicle. Sometimes, it may even send this signal without you pressing a button. These wrong signals are what can cause your car's alarm to go off for absolutely no reason at all.

How does a shock sensor work?

A shock sensor works by detecting the shockwaves that are associated with a window or a door being broken. The force behind a powerful shock wave can be detected by a shock sensor and cause it to activate. The shock sensor will then know to alert the system.

What sets a car alarm off?

How Do I Stop My Car Alarm Going Off?

1. Bad Key Fob. The simple fix for a bad key fob being the cause of your alarm going off is to check and replace the batteries.
2. Low Battery.
3. Corroded/Rusty Battery.
4. Hood Latch Sensor.
5. Poorly Installed Alarm.
6. Shock Sensors.

Why do cars have alarms?

Car alarm sensors

Modern car alarms are designed to respond to a variety of different security threats that can lead to car theft or other car crime. If one of the sensors is activated by a potential car thief, the sensor sends a signal to the computer and the alarm is activated, preventing theft or damage.

Where is the valet switch located?

Typical locations for valet switch: Under the driver's side dash (mounted in the under-dash covering trim panel or wire-tied to a harness) Mounted in the driver's side kick panel. Mounted in the steering column plastic housing.

Why did my remote start stop working?

Cause: In most cases, the under-hood pin switch is broken or corroded. Any remote starter must have a method of preventing the vehicle from starting when the hood is open. Without this, a mechanic could be seriously injured if the vehicle was remotely started while they were working on it.

How do I get my car out of valet mode?

Start the vehicle. Press and release the foot brake pedal 10 times within 10 seconds. This procedure will only deactivate Valet Mode, it will not activate Valet Mode. The vehicles parking lights should flash twice to indicate the system has exited valet mode.

How do I get my Compustar remote off hold?

One button & Four button remotes:

Hold the lock button down for about 4 seconds to take the remote out of hold. Once the remote is out, it should be functional or able to program to a system.

How do I disable Compustar?

How Do I Disable my Compustar/Arctic Start Alarm When My Remote is Not Working?

1. Insert they key into the ignition.
2. Cycle the vehicle key between the OFF and ON/RUN positions 5+ times until the alarm stops. DO NOT START THE ENGINE.

Can I upgrade my Compustar remote?

Purchasing a new remote is as easy as visiting your installer. Visit the dealer who installed your system, or another Compustar Authorized Dealer, for personal advice on which remotes will work for your system and your preferences.

How do I program my remote starter key fob?

How to reprogram a key fob

1. Replace the batteries inside the key fobs.
2. Get inside the car.
3. Turn on the ignition.
4. Press the lock button on the remote key.
5. Listen for a Lock Sound.
6. Programming additional remotes.
7. Turn off the ignition.
8. Step out from your car and test the result.

What is the valet override button?

The valet button or switch permits the owner to temporarily bypass the alarm functionality of the system. To enter or exit valet mode, disarm the system with a working transmitter, your personalized manual override code, or using the procedure below which is to enter or exit valet mode.

Are Compustar remote starters good?

1. Editor's Pick: Compustar 1-Way Remote Start and Security System (CS700-AS) The Compustar CS700-AS is an all-in-one remote start and alarm bundle boasting 1,000-feet max range and is diesel-engine safe. It may not be as feature rich as other products, but it's an affordable remote start and alarm bundle.

What is Compustar?

The industry's leading remote start and security solutions - Compustar offers best in class features, vehicle compatibility, reliability, and customer service to keep you and your vehicle safe and comfortable.

What is valet mode?

Valet mode disables all system features other than lock or unlock; such as, remote start, alarm triggers, and trunk release. Valet mode is used when the vehicle will be operated by someone who is unfamiliar with an Arctic Start system.

How do I enter valet mode Compustar?

How to Enter "Valet Mode"

1. Turn the vehicle key in the ignition to the 'On' position.
2. Press and release the lock button and the trunk button simultaneously (buttons I & III).
3. Holding the buttons for over . 5 seconds will cause this to fail.

How does Compustar remote starter work?

On most push-to-start vehicles, Compustar remote starters use a secure, proprietary technology called KLON* that mimics your vehicle's smart-key signal to start your engine. Thus, when you remote start your push-to-start vehicle, your engine will start as if your smart-key was physically inside of your vehicle!